CompanyLogo
Search Advanced Search
Categories
General Questions (53)
Studio Series (20)
Evolution Series (27)
G-DRIVE Family (41)
G-RAID Family (51)
G-SPEED/G-SAFE Family (52)
G-CONNECT (53)
G-MINI (16)
G-SATA (15)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
G-CONNECT Hardware Specifications

G-CONNECT Hardware Specifications

Product Features & Diagram
The following diagram will help you become familiar with your new G-CONNECT device.

  1. Power Button

    Press the Power button on the device to turn the G-CONNECT 'On' or 'Off'. The Power/HDD light will begin to flash as the Wi-Fi light and Status light will blink when the device is turned on. The Power/HDD light will blink periodically through your work session.

    When turning the device 'Off' you will see the Power/HDD light brighten and then the Status light will blink rapidly, followed by all lights shutting off.

  2. Wi-Fi Button

    The Wi-Fi button is used to enable/disable Wi-Fi and to the device.

    In the case that you need to perform a factory reset on your G-CONNECT press and hold this button until the LED's on the front of the device begins to oscillate.

  3. Power Port

    Connect the device to the power adapter to enable wireless access.

  4. USB Port

    On the rear of the device is a USB 2.0 port and Ethernet port. Use the USB port when you mount the device on a laptop or desktop computer.

  5. Ethernet Port

    Use the Ethernet port to connect G-CONNECT to your local Internet router, and use the device as a private Wi-Fi hotspot for wireless devices.


Print  Email  Save  Notify Me  Delete from Favorites 
Article ID: 91 Article Created: 07-22-2013 13:52 PMLast Modified: 07-22-2013 14:07 PM

How well did this article answer your question? 100% 75% 50% 25% 0%

Most Recently Viewed Articles
External Drive Troubleshooting - Mac
Basic steps for troubleshooting your G-Technology external drive on the Mac...
How do I setup my drive for use as a Time Machine backup?
In most cases when a new drive is connected to the system Time Machine will prompt you for the setup. If this does not   happen or if you are... ...
Safely Ejecting Your G-Technology Drive
 How to properly eject your drive before disconnecting or powering off....
Can I daisy chain Thunderbolt 2 and Thunderbolt 1 devices?
Yes, but if you would do that, make sure that the Thunderbolt 1 devices are placed after the Thunderbolt 2 devices. If a Thunderbolt 2 device would be daisy chained after a Thunderbolt 1 device, it will operate at Thunderbolt 1 speeds.  ...
Will my Thunderbolt 1 devices work with Thunderbolt 2?
Yes, the Thunderbolt 2 uses the same connectors, thus the Thunderbolt 1 device will work, but the Thunderbolt 2 port will perform at Thunderbolt 1 speeds (10Gbps) ...
What is Thunderbolt 2?
Thunderbolt 2 uses the same size port and Thunderbolt cable, but doubles the speed by using a controller chip that uses the original two 10Gbps bi-directional channels and combines them into a single 20Gbps bi-directional channel. Thunderbolt 2 will also support DisplayPort 1.2, which enables video streaming to one 4k monitor, or dual QHD displays. Thunderbolt 2 is backward compatible with Thunderbolt.  ...
How much space will I have available in RAID?
    ...
Which RAID Set should I use?
Depending on your requirements, there are 5 different types of RAID configurations available that are outlined in this article....
What happens when I pull the Thunderbolt cable out of the host or the G-RAID Studio while the host is still powered on?
  ...
How do I know which hard drive has failed in JBOD?
  ...