CompanyLogo
Search Advanced Search
Categories
General Questions (41)
G-CONNECT (53)
G-DRIVE ev (6)
G-DRIVE ev PLUS (6)
G-DOCK ev with Thunderbolt (15)
G-DRIVE (21)
G-DRIVE mini (25)
G-DRIVE mobile (18)
G-DRIVE mobile USB (17)
G-DRIVE slim (17)
G-MINI (16)
G-RAID (26)
G-RAID (legacy) (22)
G-RAID mini (25)
G-RAID Thunderbolt (15)
G-SATA (15)
G-SAFE (19)
G-SPEED (24)
G-SPEED Q (25)
G-SPEED eS PRO (21)
G-SPEED eS (33)
G-SPEED FC (16)
G-SPEED FC XL (20)
XL 12 (14)
XL 16 (14)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
I forgot my G-CONNECT Wireless Network Password

I forgot my G-CONNECT Wireless Network Password

There may be certain situations in which you need to reset* the G-CONNECT device. Typically, this happens when you misplace or lose your Wireless Network SSID password.


To reset the device, please follow the steps below:

  1. Power on the device and wait for the Status LED to stop flashing.
  2. Press and hold the small round button labeled Wi-Fi found on the back of the
    G-CONNECT for 10 seconds or until the Status LED begins to rapidly flash. Once the lights begin to flash, you can release the Wi-Fi button.
  3. The reset process can take up to 2 minutes. Please do not power off the device while the reset is occurring.
  4. The G-CONNECT will either power off or the lights will stop flashing. This indicates the process is complete.
  5. You are now ready to run through the Web Application Setup process and reconfigure your G-CONNECT.

* When you reset your device, certain information that had been entered during setup will not be saved (e.g. your Wireless network SSID and password). You will need to run through the Web Application Setup process again. Any saved Favorites and all Preference Settings will not remain 'saved', however, all your content will still be available.


Print  Email  Save  Notify Me  Delete from Favorites 
Article ID: 135 Article Created: 07-22-2013 17:24 PMLast Modified: 07-22-2013 17:24 PM

How well did this article answer your question? 100% 75% 50% 25% 0%

Most Recently Viewed Articles
What is the difference between the G-DRIVE and G-RAID?
   ...
I recreated my raid using the web GUI but I don't see my hard drive on the desktop
  ...
How to Connect in USB Mode
First if you have already powered on the device, you will need to power it off by pressing the power button found on the device until the LED's begin flashing. When the LED's turn off, it is safe to disconnect the power adapter. Plug the two identical ends of the Y-Cable into your personal computer and the third into your G-CONNECT....
On Windows I can't initialize my G-Technology hard drive. Disk Management says it is a "GPT Protective Partition."
On a Windows system drives show up as a "GPT protective partition" and are unable to be formatted. REASON: G-Technology drives are formatted at the factory for Mac OS.  Changes to the Mac OS in 10.5 and above have caused an incompatibility with Windows OS, requiring the drive to be "cleaned" before being formatted.  The process to "clean" the drive outlined in this article. ...
Formatting NTFS for Windows
 This article contains information on how to format your G-Technology Hard Drive in NTFS for use with Windows....
How do I setup my G-Technology drive for use with Time Machine?
G-Technology drives are designed to be compatible with the Apple Time Machine software....
How do I restore the look of my drive icon after I've formatted my G-Technology drive on the Mac?
 Follow these instructions to restore the look of your G-Technology drive icons after formatting on Mac....
External Drive Troubleshooting - Mac
Basic steps for troubleshooting your G-Technology external drive on the Mac...
Setting up G-CONNECT
To get started, you will need your G-CONNECT, a personal computer with a web browser installed. Please review the System Requirements section to make sure you have a supported operating system and web browser....
How do I initialize G-RAID?
How to initialize G-RAID on Macintosh or Windows system....